By Rae Lee | 16 April 2020 | 0 Comments
You need a little bit of camera maintenance
Against dust, Canon and Nikon's SLR structure still have advantages over the micro-single. After all, the mirror box can usually block a lot of dust. Even this time the reflector and shutter are dirty, because the SLR is deeper than the sensor, it is slightly dirtier than Sony's full picture. At the same time as SLR, because the Nikon bayonet is smaller than Canon, the distance between cmos and bayonet is longer than Canon, so it is the most difficult to dirty several products (that is, usually the least likely to get ash in theory).
How to manually clean the shooting equipment？
1. To clean the fuselage, you can first brush off most of the dust with a toothbrush or brush. However, brush brush brush or brush must not be used to brush lens or camera reflector, viewfinder.
2. use air blowing to blow away the surface of other dust, when using air blowing, pay attention to the fine seam of the fuselage is easy to hide dirt, is the focus of cleaning.
3. finally clean 50% of the lens to the soft cotton cloth to wipe the camera, wipe to avoid liquid from the slit into the camera interior —— need special attention, must not use other chemicals, such as alcohol will corrode the fuselage or surface of rubber —— When cleaning the fuselage, some users will use compressed air to blow away the dust in the fuselage slit, in fact, this is not appropriate. Compressed air in use will cause cooling effect, even condensed on the lcd surface to form water vapor, so the safety and effect is not as good as manual wiping. In addition, after cleaning, the camera should be placed in a dry and ventilated place without direct sunlight, after its drying before use.
LCD screen protection
Camera or camera lcd display screen is a fragile part on the camera —— easily damaged but expensive to replace, so special attention should be paid to protection during use.
To deal with dirt on the surface of the display screen (fingerprints or some grease dust are the most common on the lcd), use eyeglasses or 3 m of the company's magic cloth wipe. But be sure to be light during the wipe, while not using a strong glass cleaner, because most yard SLR lcd surface has an anti-glare film, this film can not be repaired once damaged.
In use, to avoid lcd being scratched by hard objects, if your use environment is worse, may cause lcd damage, you can buy screen savers (such as gold steel stickers or lcd covers) to enhance their protection.
Moreover, we should pay attention not to let the lcd surface be squeezed by heavy objects, but also to avoid the high temperature damage to it, as the temperature increases, the display will become black, after a certain temperature, even if the temperature drops to normal, the color LCD screen can not recover —— some display brightness will decrease with the temperature, when the temperature is quite low, the brightness of the lcd will be very low, but once the temperature rises, the brightness will automatically return to normal, a normal phenomenon.
Each machine has a lcd screen that can not be seen from the surface of the lamp, if the image of the darkening, or the image of the spot, or can not be displayed at all, mostly due to the aging of the bulb, in this case, generally to replace the corresponding bulb. For the sake of LCD safety, it is recommended that you always install it on the machine.
Clean sensor dust
Because of the influence of static electricity, the photosensitive chip is very easy to stain dust, most of the current equipment has dust removal system, in peacetime we can use it to clean the photosensitive chip. But in the face of machine automatic cleaning can not eliminate the stubborn stains, manual cleaning is still necessary.
If conditions permit, prepare an air blow (the size of the mouth must be mung bean), a laptop vacuum cleaner and a wide circle of transparent tape. After the material is ready, bake the air-blown blow nozzle slightly with a lighter (to remove the burr of the plastic blow nozzle) first. Fix the other end of the balloon with the suction pipe mouth of the vacuum cleaner, and finally seal it with transparent tape, then the vacuum cleaner can be opened for dust removal (need to manually adjust the power of the vacuum cleaner, if the balloon suction is large, will naturally gravure, generally grasp the balloon when the suction is the most suitable). Because the air flow of this method is suction rather than blowing, it will not form a strong pressure on the sensor, and the suction nozzle force is very small, and it is far from damaging any electronic component.
Notes:
If you are out of the door, you can take the machine's bayonet down, then select the camera's m gear, and then set it to 30 seconds of exposure (you can also use the reflector pop-up function, but be sure to have enough electricity, if there is no electricity in the middle of the way, the reflector will suddenly fall will have serious consequences), and then blow off the dust on the photosensitive chip with air blowing. A more safe way, of course, is to set the camera to a b door, then release the shutter with the shutter line and lock it, and then we can safely blow the dust, and then close the shutter when the photosensitive chip is clean (the micro-single and the camera are not so troublesome, can blow directly to the photosensitive chip).
If you need to buy a high-quality, low-priced products,access to our stores please! We have many sizes for you picking!
Click the link below to enter~
https://www.lingofoto.com/
How to manually clean the shooting equipment？
1. To clean the fuselage, you can first brush off most of the dust with a toothbrush or brush. However, brush brush brush or brush must not be used to brush lens or camera reflector, viewfinder.
2. use air blowing to blow away the surface of other dust, when using air blowing, pay attention to the fine seam of the fuselage is easy to hide dirt, is the focus of cleaning.
3. finally clean 50% of the lens to the soft cotton cloth to wipe the camera, wipe to avoid liquid from the slit into the camera interior —— need special attention, must not use other chemicals, such as alcohol will corrode the fuselage or surface of rubber —— When cleaning the fuselage, some users will use compressed air to blow away the dust in the fuselage slit, in fact, this is not appropriate. Compressed air in use will cause cooling effect, even condensed on the lcd surface to form water vapor, so the safety and effect is not as good as manual wiping. In addition, after cleaning, the camera should be placed in a dry and ventilated place without direct sunlight, after its drying before use.
LCD screen protection
Camera or camera lcd display screen is a fragile part on the camera —— easily damaged but expensive to replace, so special attention should be paid to protection during use.
To deal with dirt on the surface of the display screen (fingerprints or some grease dust are the most common on the lcd), use eyeglasses or 3 m of the company's magic cloth wipe. But be sure to be light during the wipe, while not using a strong glass cleaner, because most yard SLR lcd surface has an anti-glare film, this film can not be repaired once damaged.
In use, to avoid lcd being scratched by hard objects, if your use environment is worse, may cause lcd damage, you can buy screen savers (such as gold steel stickers or lcd covers) to enhance their protection.
Moreover, we should pay attention not to let the lcd surface be squeezed by heavy objects, but also to avoid the high temperature damage to it, as the temperature increases, the display will become black, after a certain temperature, even if the temperature drops to normal, the color LCD screen can not recover —— some display brightness will decrease with the temperature, when the temperature is quite low, the brightness of the lcd will be very low, but once the temperature rises, the brightness will automatically return to normal, a normal phenomenon.
Each machine has a lcd screen that can not be seen from the surface of the lamp, if the image of the darkening, or the image of the spot, or can not be displayed at all, mostly due to the aging of the bulb, in this case, generally to replace the corresponding bulb. For the sake of LCD safety, it is recommended that you always install it on the machine.
Clean sensor dust
Because of the influence of static electricity, the photosensitive chip is very easy to stain dust, most of the current equipment has dust removal system, in peacetime we can use it to clean the photosensitive chip. But in the face of machine automatic cleaning can not eliminate the stubborn stains, manual cleaning is still necessary.
If conditions permit, prepare an air blow (the size of the mouth must be mung bean), a laptop vacuum cleaner and a wide circle of transparent tape. After the material is ready, bake the air-blown blow nozzle slightly with a lighter (to remove the burr of the plastic blow nozzle) first. Fix the other end of the balloon with the suction pipe mouth of the vacuum cleaner, and finally seal it with transparent tape, then the vacuum cleaner can be opened for dust removal (need to manually adjust the power of the vacuum cleaner, if the balloon suction is large, will naturally gravure, generally grasp the balloon when the suction is the most suitable). Because the air flow of this method is suction rather than blowing, it will not form a strong pressure on the sensor, and the suction nozzle force is very small, and it is far from damaging any electronic component.
Notes:
If you are out of the door, you can take the machine's bayonet down, then select the camera's m gear, and then set it to 30 seconds of exposure (you can also use the reflector pop-up function, but be sure to have enough electricity, if there is no electricity in the middle of the way, the reflector will suddenly fall will have serious consequences), and then blow off the dust on the photosensitive chip with air blowing. A more safe way, of course, is to set the camera to a b door, then release the shutter with the shutter line and lock it, and then we can safely blow the dust, and then close the shutter when the photosensitive chip is clean (the micro-single and the camera are not so troublesome, can blow directly to the photosensitive chip).
If you need to buy a high-quality, low-priced products,access to our stores please! We have many sizes for you picking!
Click the link below to enter~
https://www.lingofoto.com/
Leave a Reply
Your email address will not be published.Required fields are marked. *